| |
If you just made a post, click here to view it.
MARK merc383@aol.com
03-30-2009 4:27:39 PM CST
CAN'T WAIT TO GET BACK TO THE TRACK. SEE YOU AT CARLISLE GUYS!!!
MARK merc383@aol.com
03-30-2009 4:22:56 PM CST
JUST FIRED UP MY 65 CALIENTE AFTER 13 MONTHS OF REBUILDING. 24K ORIGINAL MILES!!!
dominick doms6453@hotmail.com
03-24-2009 5:56:18 PM CST
To see full pics of the build on my fairlane go to cardomain and go under 1964 ford fairlane and mine should be one of the top 3 take a look and tell me what ya think
dominick doms6453@hotmail.com
03-24-2009 5:52:03 PM CST
my 64 fairlane daily driver i built
Jim Davis jimskb@comcast.net
03-24-2009 2:06:59 PM CST
 Just wanted to show off my 67 Fairlane, with 347 Crate motor and 490 HP
kim flirty@windstream.net
03-23-2009 9:40:36 PM CST
 MY HUSBAND CHUCK IS LOOKING 4 A 73 RANCHERO DASH MUST B IN GOOD SHAPE AND REASONABLE ALSO LOOKINK 4 72 TORENO OR RANCHERO FRONT CLIP MUST BE REASONABLE AND IN GOOD SHAPE
Kevin Hortel kevinh.softstrip@att.net
03-12-2009 9:53:22 AM CST
1956 Ford Fairlane Sedan. I am looking for either door skins or complete shells for both left and right side doors. Also looking for hood and trunk lid for 56 Ford Fairlane Sedan! Any help will be appreciated. Kevin
jered jdsilver1984@yahoo.com
03-01-2009 6:30:10 PM CST
 Does a 460 engine fit in a 1967 fairlane with out cutting the shock towers.
Chris Petrie chrispetrie@bresnan.net
02-21-2009 12:16:05 AM CST
Looking for advice about installing 3 point safety belts, and have been warned that there is not enough room to mount the anchor to the post. Anyone with exprience on this topic?
Brian bgs2222@hotmail.com
02-17-2009 10:12:23 PM CST
My understanding with the leaf spring relocation kit I will gain an additional 6” or 3” LH/RH. The car originally came with 14” tires…with the conversion can I assume 15” will fit? I also had a new drive shaft put in for additional room years ago. How wide of a tire in the rear is recommended?
Falcon Ed
02-06-2009 7:26:50 PM CST
Restoring a dash mount tac in a 64 falcon. Does anyone know hot to get into this unit? I need a new dile and lens. It looks sealed but someone said it takes a certen tool. Call a tac repair shop but he said he no longer worked on them because of that.
John elsimons@goldenwest.net
02-06-2009 7:10:21 PM CST
 Looking for a good hood for 1966 GT Fairlane
Bob bhershberger41@yahoo.com
01-28-2009 10:44:54 AM CST
I'm putting an FE into a 75 stang and want to know what headers will work on this combo ( if any ). Also need to know where to buy motor plates. Any help would be appreciated, thanks.
Bonzi. jwc@dslextreme.com
01-26-2009 1:50:11 PM CST
I have a 1963 Ranchero, the top is in bad shape but it is strong and the rest of the body is in good shape. I would like to cut the top off and make a Ranchero/Roadster. Has any one done this and if so tell me were to brace the frame before we cut the top off?
Thanks, Bonzi Jim
fred vogel vogelelectric@gmail.com
01-05-2009 10:16:52 PM CST
 does anyone out there know if a 65 cyclone hood fits a 65 falcon.
Johnny Hinton rethinton@yahoo.com
01-03-2009 10:44:03 AM CST
 I have a 69 Torino Fastback that I need all 4 wheelwell trim pieces.
Dick Monaco dragsterdick@comcast.net
12-13-2008 1:45:25 PM CST
Wanting to sell or trade a great 32 Ford Street Rod for an early 60's Ford Galaxie race car or a 64 Thunderbolt clone!! Check out my add#1390015 on (racingjunk.com) Call me anytime at 630-494-1065
Terry Fife tmf@netscope.net
11-30-2008 3:35:08 PM CST
Hi does anyone have the passing gear kickdown linkage and the kickdown rod that comes from the trans to the linkage for a 66 67 fairlane 390 gt C6 trans auto in the floor , i have looked every where need help
Thanks Terry Fife
Joe j-kharbolt@hotmail.com
11-24-2008 12:45:35 PM CST
This car for sale and parts car w/cites fiberglass on it... fenders deck lid
have some other parts for a 66-67 fairlane
Joe
419-961-7972
brian buckhornbrian@yahoo.com
11-16-2008 5:29:59 PM CST
here is a pic of the all aluminum mock up motor and i will be pitting a dove 427 stroker in my 1987 fox body drag radial race car i am looking for some headers and motor plates? any help? is there any sites out there where i can find some photos?
JOE 810-599-6402 JCOUCHMAN@DGEQUIPMENT.COM
11-03-2008 2:59:36 PM CST
LOOKING FOR THE CHROME TRIM ON THE TRUNK LID FOR A 70/71, MONTEGO OR CYCLONE 810-599-6402
THANKS
Ernie
11-03-2008 8:06:26 AM CST
Looking for a tailgate for a 1962 comet wagon
steven Stevies_falcon@yahoo.com
10-17-2008 2:41:20 PM CST
Does anybody know if the DOVE high riser heads and single 4v manifold will fit under the hood of a 1969 fairlane with or with out the factory ram air scoop or will i need more room.
Jr saleen54@netzero.net
10-16-2008 8:53:40 AM CST
Looking for a pair of Crites headers for a 351w into a 1964 Fairlane, Crites no longer makes them! thnx 360-931-2239
Andy tinnovations@comcast.net
10-09-2008 4:27:37 PM CST
Looking for a 64 post car "shell" something to do a tube chassis out of , don't want to cut mine up the floor and frame a in real good shape . thanks
PREV
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
NEXT
|
|
|
|
|
|